pwmc.c File Reference

#include "chip.h"
#include <stdint.h>
#include <assert.h>

Functions
void	PWMC_ConfigureChannel (Pwm *pPwm, uint8_t channel, uint32_t prescaler, uint32_t alignment, uint32_t polarity)
	Configures PWM a channel with the given parameters, basic configure function. More...
void	PWMC_ConfigureChannelExt (Pwm *pPwm, uint8_t channel, uint32_t prescaler, uint32_t alignment, uint32_t polarity, uint32_t countEventSelect, uint32_t DTEnable, uint32_t DTHInverte, uint32_t DTLInverte)
	Configures PWM a channel with the given parameters, extend configure function. The PWM controller must have been clocked in the PMC prior to calling this function. Beware: this function disables the channel. It waits until disable is effective. More...
void	PWMC_ConfigureClocks (Pwm *pPwm, uint32_t clka, uint32_t clkb, uint32_t mck)
	Configures PWM clocks A & B to run at the given frequencies. More...
void	PWMC_SetPeriod (Pwm *pPwm, uint8_t channel, uint16_t period)
	Sets the period value used by a PWM channel. More...
void	PWMC_SetDutyCycle (Pwm *pPwm, uint8_t channel, uint16_t duty)
	Sets the duty cycle used by a PWM channel. This function writes directly to the CDTY register if the channel is disabled; otherwise it uses the update register CDTYUPD. Note that the duty cycle must always be inferior or equal to the channel period. More...
void	PWMC_SetDeadTime (Pwm *pPwm, uint8_t channel, uint16_t timeH, uint16_t timeL)
	Sets the dead time used by a PWM channel. This function writes directly to the DT register if the channel is disabled; otherwise it uses the update register DTUPD. Note that the dead time must always be inferior or equal to the channel period. More...
void	PWMC_ConfigureSyncChannel (Pwm *pPwm, uint32_t channels, uint32_t updateMode, uint32_t requestMode, uint32_t requestComparisonSelect)
	Configures Synchronous channel with the given parameters. Beware: At this time, the channels should be disabled. More...
void	PWMC_SetSyncChannelUpdatePeriod (Pwm *pPwm, uint8_t period)
	Sets the update period of the synchronous channels. This function writes directly to the SCUP register if the channel #0 is disabled; otherwise it uses the update register SCUPUPD. More...
void	PWMC_SetSyncChannelUpdateUnlock (Pwm *pPwm)
	Sets synchronous channels update unlock. More...
void	PWMC_EnableChannel (Pwm *pPwm, uint8_t channel)
	Enables the given PWM channel. More...
void	PWMC_DisableChannel (Pwm *pPwm, uint8_t channel)
	Disables the given PWM channel. More...
void	PWMC_EnableChannelIt (Pwm *pPwm, uint8_t channel)
	Enables the period interrupt for the given PWM channel. More...
uint32_t	PWMC_GetStatus2 (Pwm *pPwm)
	Return PWM Interrupt Status2 Register.
void	PWMC_DisableChannelIt (Pwm *pPwm, uint8_t channel)
	Disables the period interrupt for the given PWM channel. More...
void	PWMC_EnableIt (Pwm *pPwm, uint32_t sources1, uint32_t sources2)
	Enables the selected interrupts sources on a PWMC peripheral. More...
void	PWMC_DisableIt (Pwm *pPwm, uint32_t sources1, uint32_t sources2)
	Disables the selected interrupts sources on a PWMC peripheral. More...
void	PWMC_SetOverrideValue (Pwm *pPwm, uint32_t value)
	Set PWM output override value. More...
void	PWMC_EnableOverrideOutput (Pwm *pPwm, uint32_t value, uint32_t sync)
	Enable override output. More...
void	PWMC_OutputOverrideSelection (Pwm *pPwm, uint32_t value)
	Output Selection for override PWM output. More...
void	PWMC_DisableOverrideOutput (Pwm *pPwm, uint32_t value, uint32_t sync)
	Disable override output. More...
void	PWMC_SetFaultMode (Pwm *pPwm, uint32_t mode)
	Set PWM fault mode. More...
void	PWMC_FaultClear (Pwm *pPwm, uint32_t fault)
	PWM fault clear. More...
void	PWMC_SetFaultProtectionValue (Pwm *pPwm, uint32_t value)
	Set PWM fault protection value. More...
void	PWMC_EnableFaultProtection (Pwm *pPwm, uint32_t value)
	Enable PWM fault protection. More...
void	PWMC_ConfigureComparisonUnit (Pwm *pPwm, uint32_t x, uint32_t value, uint32_t mode)
	Configure comparison unit. More...
void	PWMC_ConfigureEventLineMode (Pwm *pPwm, uint32_t x, uint32_t mode)
	Configure event line mode. More...

Detailed Description

Implementation of the Pulse Width Modulation Controller (PWM) peripheral.

Function Documentation

PWMC_ConfigureChannel()

void PWMC_ConfigureChannel	(	Pwm *	pPwm,
		uint8_t	channel,
		uint32_t	prescaler,
		uint32_t	alignment,
		uint32_t	polarity
	)

Configures PWM a channel with the given parameters, basic configure function.

The PWM controller must have been clocked in the PMC prior to calling this function. Beware: this function disables the channel. It waits until disable is effective.

Parameters

channel	Channel number.
prescaler	Channel prescaler.
alignment	Channel alignment.
polarity	Channel polarity.

PWMC_ConfigureChannelExt()

void PWMC_ConfigureChannelExt	(	Pwm *	pPwm,
		uint8_t	channel,
		uint32_t	prescaler,
		uint32_t	alignment,
		uint32_t	polarity,
		uint32_t	countEventSelect,
		uint32_t	DTEnable,
		uint32_t	DTHInverte,
		uint32_t	DTLInverte
	)

Configures PWM a channel with the given parameters, extend configure function. The PWM controller must have been clocked in the PMC prior to calling this function. Beware: this function disables the channel. It waits until disable is effective.

Parameters

channel	Channel number.
prescaler	Channel prescaler.
alignment	Channel alignment.
polarity	Channel polarity.
countEventSelect	Channel counter event selection.
DTEnable	Channel dead time generator enable.
DTHInverte	Channel Dead-Time PWMHx output Inverted.
DTLInverte	Channel Dead-Time PWMHx output Inverted.

PWMC_ConfigureClocks()

void PWMC_ConfigureClocks	(	Pwm *	pPwm,
		uint32_t	clka,
		uint32_t	clkb,
		uint32_t	mck
	)

Configures PWM clocks A & B to run at the given frequencies.

This function finds the best MCK divisor and prescaler values automatically.

Parameters

clka	Desired clock A frequency (0 if not used).
clkb	Desired clock B frequency (0 if not used).
mck	Master clock frequency.

PWMC_ConfigureComparisonUnit()

void PWMC_ConfigureComparisonUnit	(	Pwm *	pPwm,
		uint32_t	x,
		uint32_t	value,
		uint32_t	mode
	)

Configure comparison unit.

Parameters

x	comparison x index
value	comparison x value.
mode	comparison x mode

PWMC_ConfigureEventLineMode()

void PWMC_ConfigureEventLineMode	(	Pwm *	pPwm,
		uint32_t	x,
		uint32_t	mode
	)

Configure event line mode.

Parameters

x	Line x
mode	Bitwise OR of line mode selection

PWMC_ConfigureSyncChannel()

void PWMC_ConfigureSyncChannel	(	Pwm *	pPwm,
		uint32_t	channels,
		uint32_t	updateMode,
		uint32_t	requestMode,
		uint32_t	requestComparisonSelect
	)

Configures Synchronous channel with the given parameters. Beware: At this time, the channels should be disabled.

Parameters

channels	Bitwise OR of Synchronous channels.
updateMode	Synchronous channel update mode.
requestMode	PDC transfer request mode.
requestComparisonSelect	PDC transfer request comparison selection.

PWMC_DisableChannel()

void PWMC_DisableChannel	(	Pwm *	pPwm,
		uint8_t	channel
	)

Disables the given PWM channel.

Beware, channel will be effectively disabled at the end of the current period. Application can check channel is disabled using the following wait loop: while ((PWM->PWM_SR & (1 << channel)) != 0);

Parameters

channel

Channel number.

PWMC_DisableChannelIt()

void PWMC_DisableChannelIt	(	Pwm *	pPwm,
		uint8_t	channel
	)

Disables the period interrupt for the given PWM channel.

Parameters

channel

Channel number.

PWMC_DisableIt()

void PWMC_DisableIt	(	Pwm *	pPwm,
		uint32_t	sources1,
		uint32_t	sources2
	)

Disables the selected interrupts sources on a PWMC peripheral.

Parameters

sources1	Bitwise OR of selected interrupt sources of PWM_IDR1.
sources2	Bitwise OR of selected interrupt sources of PWM_IDR2.

PWMC_DisableOverrideOutput()

void PWMC_DisableOverrideOutput	(	Pwm *	pPwm,
		uint32_t	value,
		uint32_t	sync
	)

Disable override output.

Parameters

value	Bitwise OR of output selection.
sync	0: enable the output asynchronously, 1: enable it synchronously

PWMC_EnableChannel()

void PWMC_EnableChannel	(	Pwm *	pPwm,
		uint8_t	channel
	)

Enables the given PWM channel.

This does NOT enable the corresponding pin;this must be done in the user code.

Parameters

channel

Channel number.

PWMC_EnableChannelIt()

void PWMC_EnableChannelIt	(	Pwm *	pPwm,
		uint8_t	channel
	)

Enables the period interrupt for the given PWM channel.

Parameters

channel

Channel number.

PWMC_EnableFaultProtection()

void PWMC_EnableFaultProtection	(	Pwm *	pPwm,
		uint32_t	value
	)

Enable PWM fault protection.

Parameters

value

Bitwise OR of FPEx[y].

PWMC_EnableIt()

void PWMC_EnableIt	(	Pwm *	pPwm,
		uint32_t	sources1,
		uint32_t	sources2
	)

Enables the selected interrupts sources on a PWMC peripheral.

Parameters

sources1	Bitwise OR of selected interrupt sources of PWM_IER1.
sources2	Bitwise OR of selected interrupt sources of PWM_IER2.

PWMC_EnableOverrideOutput()

void PWMC_EnableOverrideOutput	(	Pwm *	pPwm,
		uint32_t	value,
		uint32_t	sync
	)

Enable override output.

Parameters

value	Bitwise OR of output selection.
sync	0: enable the output asynchronously, 1: enable it synchronously

PWMC_FaultClear()

void PWMC_FaultClear	(	Pwm *	pPwm,
		uint32_t	fault
	)

PWM fault clear.

Parameters

fault

Bitwise OR of fault to clear.

PWMC_OutputOverrideSelection()

void PWMC_OutputOverrideSelection	(	Pwm *	pPwm,
		uint32_t	value
	)

Output Selection for override PWM output.

Parameters

value

Bitwise OR of output override value.

PWMC_SetDeadTime()

void PWMC_SetDeadTime	(	Pwm *	pPwm,
		uint8_t	channel,
		uint16_t	timeH,
		uint16_t	timeL
	)

Sets the dead time used by a PWM channel. This function writes directly to the DT register if the channel is disabled; otherwise it uses the update register DTUPD. Note that the dead time must always be inferior or equal to the channel period.

Parameters

channel	Channel number.
timeH	Dead time value for PWMHx output.
timeL	Dead time value for PWMLx output.

PWMC_SetDutyCycle()

void PWMC_SetDutyCycle	(	Pwm *	pPwm,
		uint8_t	channel,
		uint16_t	duty
	)

Sets the duty cycle used by a PWM channel. This function writes directly to the CDTY register if the channel is disabled; otherwise it uses the update register CDTYUPD. Note that the duty cycle must always be inferior or equal to the channel period.

Parameters

channel	Channel number.
duty	Duty cycle value.

PWMC_SetFaultMode()

void PWMC_SetFaultMode	(	Pwm *	pPwm,
		uint32_t	mode
	)

Set PWM fault mode.

Parameters

mode	Bitwise OR of fault mode.

PWMC_SetFaultProtectionValue()

void PWMC_SetFaultProtectionValue	(	Pwm *	pPwm,
		uint32_t	value
	)

Set PWM fault protection value.

Parameters

value

Bitwise OR of fault protection value.

PWMC_SetOverrideValue()

void PWMC_SetOverrideValue	(	Pwm *	pPwm,
		uint32_t	value
	)

Set PWM output override value.

Parameters

value

Bitwise OR of output override value.

PWMC_SetPeriod()

void PWMC_SetPeriod	(	Pwm *	pPwm,
		uint8_t	channel,
		uint16_t	period
	)

Sets the period value used by a PWM channel.

This function writes directly to the CPRD register if the channel is disabled; otherwise, it uses the update register CPRDUPD.

Parameters

channel	Channel number.
period	Period value.

PWMC_SetSyncChannelUpdatePeriod()

void PWMC_SetSyncChannelUpdatePeriod	(	Pwm *	pPwm,
		uint8_t	period
	)

Sets the update period of the synchronous channels. This function writes directly to the SCUP register if the channel #0 is disabled; otherwise it uses the update register SCUPUPD.

Parameters

period

update period.

PWMC_SetSyncChannelUpdateUnlock()

void PWMC_SetSyncChannelUpdateUnlock

(

Pwm *

pPwm

)

Sets synchronous channels update unlock.

Note: If the UPDM field is set to 0, writing the UPDULOCK bit to 1 triggers the update of the period value, the duty-cycle and the dead-time values of synchronous channels at the beginning of the next PWM period. If the field UPDM is set to 1 or 2, writing the UPDULOCK bit to 1 triggers only the update of the period value and of the dead-time values of synchronous channels. This bit is automatically reset when the update is done.